Meshopia · EnglishEnglish
MESHOPIAScale modelling & RC

8 tagged models · Page 1 of 1

#soporte

Discover 3D models tagged soporte and check their print information, files and terms before downloading.Search this tag in the catalogue →
Vista de Placa de batería de fondo plano para Tamiya Monster Beetle 2015

Flat-bottom battery plate for Tamiya Monster Beetle 2015

Side closure plate for the Tamiya Monster Beetle battery housing, 2015 re-edition. The author replaced the ribbed inner face with a flat surface to accommodate their battery, which was about 4 mm longer than the space available with the original plates. This measurement describes their specific case and does not guarantee an identical expansion in other units. Preparation, compatibility, and printing The source suggests PETG or PLA and considers increasing the infill to 100% around the holes. Check the length and width of your battery before printing and ensure that the plate or screws do not press against the casing. Check the closure and cable routing with the equipment turned off; do not force a battery that is still too large.

Technology
Sin probar
material
PETG, PLA
Difficulty
Sin especificar
Vista de Base para arrancador H9 de aeromodelismo

H9 model airplane starter base

Base for placing an H9 starter next to its battery. The preserved documentation mentions a three-cell 2200 mAh LiPo battery in the summary, but mentions two cells in the description. Neither of these electrical configurations is confirmed here: the allowable voltage must be obtained from the actual starter and its documentation. Preparation, compatibility, and printing Measure the starter housing and the slot intended for the battery. The base is a mechanical part; it does not adapt voltages or provide electrical protection for the assembly. Check that the fastening does not press against the battery and leaves the cables free. The source does not specify a print profile; first prepare a dimensional test of the housings.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Soporte de luces MEUS para Traxxas UDR

MEUS light bracket for Traxxas UDR

Purpose: This model is designed for mounting MEUS Racing RC LED Lights onto a Traxxas UDR. Practical uses: It serves as a light bracket for RC vehicle lighting setups. Included parts: - UDR Baja Designs Light Mount.stl Printing/assembly guidance: The author suggests printing in PETG for durability and heat resistance. It is recommended to use 100% infill to ensure durability.

Technology
Sin probar
material
PETG
Difficulty
Sin especificar
Vista de Soporte de servo con alojamiento para conector

Servo bracket with connector housing

Mount for a servomotor that incorporates a zone intended for a female servo cable connector. The design aims to house the servo and organize the cable output. The source does not identify a specific servo model or its dimensions, so compatibility must be verified in the file and with the physical component. Preparation, compatibility, and printing The hardware is described as "832" and "832 × 1 3/4"; this notation needs confirmation before purchasing or forcing screws into the part. Compare the position of the lugs and the cable path, and ensure the connector remains accessible. No material or profile is documented. Perform a fit test without powering the servo and keep the arm's range of motion clear.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Soporte de motorreductor N20 con fijaciones de 3 mm

N20 gear motor mount with 3 mm fastenings

Purpose This is a mounting bracket designed to hold N20 DC gear motors securely. The motor slides into the holder for placement. Practical Uses The author states this bracket is suitable for DIY robotics, RC cars, small rovers, and other electronics projects. Included Parts - motor holder.step - motor holder.stl Assembly Guidance The bracket can be attached to a chassis or other surface using 3 mm screws through two integrated mounting holes.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Carcasa Flywoo O4 adaptada para cámara CO3

Flywoo O4 housing adapted for CO3 camera

Housing modified from the Flywoo O4 design to house a CO3 camera. The source indicates a 25.4 × 25.4 mm mounting pattern and mentions M2 screws and threaded inserts. The modification adds material around the camera; the author's claims regarding impacts or vibrations do not equate to protection tested by Meshopia. Preparation, compatibility, and printing The author recommends TPU with supports. Check the removal of those supports and the lens clearance before slicing. Verify the exact camera, the connectors, and the clamp closure without tightening the equipment housing. The length of all screws and a confirmed final weight are not provided; measure the assembly before installing it.

Technology
Sin probar
material
TPU
Difficulty
Sin especificar
Vista de Soporte de antena para bastidor HGLRC MY5

Antenna mount for HGLRC MY5 frame

Identified antenna mount for the HGLRC MY5 frame. The original description does not provide dimensions or a list of compatible antennas and connectors. The source tags mention various FPV systems, but these are not enough to ensure that all fit on the same part. Preparation, compatibility, and printing Compare the mounting points, housing diameter, and connector space with your frame. Check that the coaxial cable is not forced and that the antenna remains outside the path of the propellers. No material or print profile is documented. A fit test allows checking the retention before installing the electronics.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Soporte en L 40 × 40 mm · ancho 30 mm · 2 agujeros Ø5 mm

Soporte en L 40 × 40 mm · ancho 30 mm · 2 agujeros Ø5 mm

Escuadra de demostración de una sola pieza, con dos alas a 90° y un agujero pasante en cada ala. La imagen de uso ilustra la unión de un panel vertical a una base horizontal. MEDIDAS • Dimensiones exteriores: 30 × 40 × 40 mm. • Ancho: 30 mm. Extensión exterior de cada ala: 40 mm. • Espesor: 4 mm. • Dos agujeros nominales Ø5 mm, centrados en el ancho a 15 mm de cada lateral. Cada centro está a 26 mm del plano exterior del encuentro y a 14 mm del extremo libre. QUÉ INCLUYE Un STL con el soporte y un archivo LEEME con medidas, unidades y comprobaciones. La madera, los tornillos y las arandelas del render son ilustrativos y no están incluidos en el STL. No se especifica un sistema de fijación validado. UNIDADES Y VERIFICACIÓN Importar el STL en milímetros y comprobar un tamaño de 30 × 40 × 40 mm: el formato STL no almacena unidades. La malla exportada tiene 804 triángulos, un único componente conectado, orientación coherente, sin bordes abiertos ni triángulos degenerados. Se verificaron digitalmente los dos pasos y el espesor. ESTADO DEL DISEÑO Modelo creado en Blender con asistencia de Codex. Las imágenes son renders, no fotografías de una impresión. No se ha impreso ni ensayado físicamente; no hay material, perfil de impresión ni carga admisible validados. Ajustar orientación, soportes, paredes, relleno y tolerancias según impresora, material y aplicación. Diseño de demostración, sin validación mecánica para usos estructurales o de seguridad.

Technology
Sin probar
material
—
Difficulty
Sin especificar