15 tagged models · Page 1 of 1

#radio control

Discover 3D models tagged radio control and check their print information, files and terms before downloading.Search this tag in the catalogue →

RC & MecánicaFree

P9 Rigger RC Boat

A model of a P9 Rigger (Outrigger) Racing Boat. The design features a front compartment intended to keep air in and water out. Testing with a 4-cell 4000Ma battery showed the model remains buoyant even when filled with water, with the outrigger and the first 6 inches of the nose staying above the waterline. Purpose: This model is designed for RC racing as a P9 Rigger (Outrigger) boat. Practical Uses: Radio-controlled racing and watercraft hobbyist use. Included Parts: - AFT_Body_Rigger_REV-D_1of3.stl - Mid_Body_Rigger_REV-D_2of3.stl - FWD_Body_Rigger_REV-D_3of3.stl - AFT_Body_Rigger_REV-D_1of2.stl - FWD_Body_Rigger_REV-D_2of2.stl - 6-Cell_AFT_Body_Rigger_REV-D_2of2.stl - 6-Cell_FWD_Body_Rigger_REV-D_1of2.stl - P-9_Rigger_Full_OutRigger.stl - P-9_AFT_OutRigger.stl - P-9_FWD_OutRigger.stl - P9_AFT_Outrigger_Rec-C_1of3.stl - P9_MID_Outrigger_Rec-C_2of3.stl - P9_FWD_Outrigger_Rec-C_3of3.stl - P9 Rigger Aft Floor.stl - P9_Rigger Servo_Bracket_Ver-2.stl - P9_Rigger_Shaft_Support_16MM.stl - P9_Rigger_Shaft_Support_19MM.stl - P9_Rigger_Shaft_Support_21MM.stl - P9_Rigger_Drive_Tube_Upper_Mount.stl - P9_Rigger_Full_Canopy.stl - P9_Rigger_Templet_1_Turn_Fin.stl - P9_Rigger_Templet_2_Turn_Fin.stl - Outrigger_Lock_Collar.stl - P9_Rigger_Motor_Mount.stl - P9_Canopy_Holdown.stl - P9_Rigger_FWD_Canopy_1 of 2.stl - P9_Rigger_AFT_Canopy_2 of 2.stl - P9_Rear_Hatch_Holdown.stl - P9_Rigger_Flat_Rear_Hatch.stl - P9_Rear_Hatch.stl Printing and Assembly Guidance: - The 6-cell body must be printed using PETG or a similar strong filament. - Print settings: 1.2mm resolution, 20% infill for the main body and outriggers, and use supports. No rafts are required. - Assemble the boat using medium or thick CA glue. - The body and canopy include 2mm alignment holes to assist with assembly. - The design is intended to use carbon fiber, piano wire, or wood as a dowel. - The 3-piece outrigger is designed to use 100mm x 5mm carbon fiber rods for strength. - The boat is designed to take 7.8mm arrows cut down to 533mm (21"). - Turn fin templates are provided for fabricating a fin from 0.8mm aluminum or metal.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

RC Airplane Clevis 25mm Length 4mm Thickness 1.5mm Hole

RC airplane clevis (chape) with a length of 25mm and a thickness of 4mm. This component is designed to facilitate connections within a remote-controlled aircraft setup. Purpose The purpose of this model is to serve as a clevis for RC airplanes, providing a mechanical connection point between control components. Practical Uses This part is used to connect a threaded rod via a 1.5mm hole and to attach a servo arm (guignol) using a 2mm hole. Included Parts The model is provided in two STL files: - Chape-AvionRC-L25-Ep4-trou1.5 v1.stl - Chape-AvionRC-L25-Ep4-trou1.5 v2.stl

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

Nokia BL-5C to FS-B800 FS800B B800 Battery Adapter

Nokia BL-5C to FS-B800/FS800B/B800 Battery Adapter

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

RC Servo Wire Strap

RC Servo Wire Strap Purpose This model is designed to tame and secure RC servo wires. The part utilizes a support structure that creates a pattern intended to lightly grip the wires in place. Practical Uses It is used in radio control applications to organize and manage servo wiring. Included Parts - wire bracket.stl - Requires an M1.5 screw for use. Printing and Assembly Guidance The author suggests printing 5, 6, or more units at a time due to their small size. When necessary, the brim should be peeled off. Suggested print settings: - Print Quality: 0.12 SUPER - Build Plate Adhesion: Brim - Brim Line Count: 4 - Generate Support: TRUE - Z Seam Alignment: Random - Infill Density: 100%

Technology: Sin probar
material: —
Difficulty: Sin especificar

HerramientasFree

RC Tool Holder and Tray

This model is a tool holder and tray designed to keep RC tools organized and ready for use. It is intended for hobbyists working with RC cars, RC planes, or racing equipment. Included files: - rc tool holder and tray.stl

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

Radiomaster TX16S Transmitter Tray

Purpose This is a transmitter tray designed specifically for the Radiomaster TX16S, featuring a folding handle. Practical Uses The tray is intended for use with RC aircraft controllers and is designed for outdoor use. Included Parts - Tray stiffener.3mf - front support.3mf - lanyard standoffs.3mf - tray base front.3mf - tray base rear.3mf - tray stiffener v10_0.4n_0.2mm_PETG_MK3S_1h43m.gcode - tray base back v6_0.4n_0.2mm_PETG_MK3S_6h50m.gcode - front support easy tx removal_0.4n_0.2mm_PETG_MK3S_2h0m.gcode - tray base front v6_0.4n_0.2mm_PETG_MK3S_2h37m.gcode - tray lanyard standoffs v6_0.4n_0.2mm_PETG_MK3S_2h57m.gcode Printing and Assembly Guidance The author reports printing all parts in PETG using a 0.4mm nozzle, a 240C nozzle temperature, and a 90C bed temperature with 15% infill on a Satin sheet with Kores application. To complete the assembly, additional parts are required: 1/4in bow shackles, an 8mm carbon fiber tube, and a neck strap (the author suggests cutting the buckle off an adjustable anti-drop lanyard).

Technology: Sin probar
material: —
Difficulty: Sin especificar

ElectrónicaFree

Associated Monster GT Truck R/C Car Stand

Purpose This jack stand and test stand is designed for the Monster GT and other RC cars or trucks. It is intended to hold the vehicle snug and firm off the ground for warming up and tuning purposes. Practical Uses The stand provides a stable platform to keep an RC vehicle elevated during maintenance or testing. Included Parts MGT STAND TOP (1).stl MGT STAND BASE.stl SPLIT-BASE PART 1.stl SPLIT-BASE PART 2.stl Printing/Assembly Guidance The base model does not include cutouts. The author suggests adding cutouts in Cura using 6 bottom layers to create screw pockets for holding small screws while working.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

3D Printable RC Car Chassis — 160 & 180 mm Wheelbase

Build a custom RC car with this downloadable set of 24 STL files. The package includes two chassis variants with 160 mm and 180 mm wheelbases, plus drivetrain, steering, wheel and mounting components. Included parts: • Chassis: 160 mm and 180 mm wheelbase options • Main-shaft and motor gears, gear sleeve and axle transmission gears • Universal joints A/B/C and dogbone drive shafts • Front/rear axles, wheel axles, wheel brackets and rear wheel mounts • Steering knuckles and linkage, servo mounting plate and linkage • Wheel rims, TPU tire models, brake parts, brake discs and shock-absorber plates All STL filenames are in English. Quantity hints in the filenames follow the supplied source names; inspect each model in your slicer before choosing the number of copies. Choose the chassis variant that suits your build. This is a digital download, not an assembled vehicle. Electronics and non-printed hardware are not included. Assembly instructions, a hardware bill of materials and tested print settings were not supplied with this package. Check fit, clearances and component compatibility before printing or assembly. The cover is an AI-generated illustrative image and is not a photograph of a verified assembled build.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

1:10 OpenRC F1 2023 RC Car — 3D Printable STL Parts

Create your next open-wheel RC project with this 1:10 OpenRC F1 2023 parts package. The download contains 37 STL files for the body, chassis, steering, rear drivetrain, wings, wheels and detail parts. Included components: • Body and frame: center body, front/rear chassis plates, rear chassis, front vented section, lid and motor cover • Front steering module: upper/lower parts, front block, wheel axle, left/right hubs, servo saver and steering push pin • Rear drive: rear axle, pinion and spur gears, and left/right wheel axle holders • Aero and details: nose, front and rear wings, halo, mirrors, camera, shark fin and rain-light diffuser • Wheels: front/rear rims, front/rear tires and wheel lock nut • Extra parts: vented lid and servo holder Original author: Lucas. License: CC0. Filenames have been standardized in English; the supplied geometry is unchanged. Digital files only. Electronics and non-printed hardware are not included. No assembly guide, hardware bill of materials or tested print settings were supplied in this folder. Inspect each part in your slicer and check fit, quantities and compatibility before printing and assembly. The supplied cover is an AI-generated illustration, not a photograph of a verified assembled model.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

Cyberbrick RC Dumptruck — 3D Printable Articulated Truck Parts

Build your next RC construction project with this Cyberbrick RC Dumptruck package: 77 STL files covering the front assembly, rear assembly, articulated hinge, transmission, wheels and 60 mm cylinder components. Included parts: • Front assembly: cab, roof, hood, frame, bumper, grille, fenders, platforms, light inserts, axle and drivetrain components • Rear assembly: rear frame, dump bed sections, tailgate and connecting rod, axle parts, wheel holders and cylinder mounts • Articulation: front/rear hinge, hinge clip and axle • Transmission: differential assembly, axle housing, frames, axles, 18-tooth outer gear and 9-tooth spur gear • Cylinder parts: housing, back housing, 60 mm rod, N20 cylinder rod components and clips • Wheels: rim, tire and mirrored tire • Additional clips, washer and non-motorized axle variant Original author: Lucas. License: CC0. English filenames include assembly prefixes to distinguish parts with similar names. STL geometry is unchanged. Digital files only. Electronics, motors and non-printed hardware are not included. No assembly manual, hardware bill of materials or tested print settings were supplied. Scale and specific Cyberbrick electronics compatibility are not verified. Check quantities, fit and component requirements before printing and assembly. The supplied cover is an AI-generated illustration and does not document a verified assembled model.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

TBS Mambo Gimbal Protector

This model is a protector designed for the Team Black Sheep Mambo radio gimbal and switch. According to the author, the device locks into place using a strap clip. Practical uses include protecting the gimbal and switch components of the TBS Mambo radio. Included parts: mambo stick protector.stl ON-DEMAND INSPECTION COPY An additional source-derived STL simplifies dense triangles for interactive inspection. Source coordinate units are preserved. Original downloads remain unchanged; use them for fine details and fabrication checks.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

Jumper T8SG Endcap

This model is an endcap designed for the Jumper T8SG radio controller. According to the author, the purpose of this part is to improve safety and increase aesthetics. Practical Uses This component serves as a cap for the Jumper T8SG device. Included Files - Zaślepka_JumperT8SG.stl

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

SPEC Wing aileron cutting miter box

Purpose This miter box is designed to cut aileron stock to the correct angle to match the sweep of an FPVWRA Spec Wing. Practical Uses It can be used with a tool such as an X-Acto razor saw to ensure accurate cuts on aileron stock. Included Parts Miter Box.stl Printing Guidance The author reports that using three bottom and three top layers with 10% infill uses approximately 5.95m (17.88g) of filament and takes about 2h 15m, depending on the setup.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaFree

Turnigy 9x throttle stick centralizer

Purpose: This part forces the radio's throttle stick to the center position. Practical Uses: It is used for multirotor drones by installing it in the internal stick set of the Turnigy 9x radio. Included Parts: - CentralizadorStick.stl Printing/Assembly Guidance: To install, open the radio and install the part in the throttle set like the other stick.

Technology: Sin probar
material: —
Difficulty: Sin especificar

Juguetes y juegosFree

WLtoys Drift A959 Steering System Redesign

Purpose This redesigned front steering system for the WLtoys A959 is intended to increase the steering angle to improve drift performance. The design removes front traction to allow for more freedom and control during drifts. Practical Uses The system is designed for controlled drifting and smoother transitions. The modification is non-destructive, allowing the vehicle to be returned to its original state without damaging any parts. The author suggests using a gyro for an improved experience. Included Parts - brazo direccion .stl - brazo servo .stl - Drag_link .stl - horquilla .stl - masa.stl - placa direccion inf .stl - placa direccion sup .stl - Servo_Bracket .stl - soporte masa .stl Printing and Assembly Guidance The author reports all parts were printed in PETG. The horquilla (fork) and brazo de direccion (steering arm) must be printed as mirrors. Only the steering arm and servo arm require supports. Required hardware includes 10 M2 screws: 2x M2*20 and 8x M2*8.

Technology: Sin probar
material: —
Difficulty: Sin especificar