Meshopia · EnglishEnglish
MESHOPIAScale modelling & RC

13 tagged models · Page 1 of 1

#ender 3

Discover 3D models tagged ender 3 and check their print information, files and terms before downloading.Search this tag in the catalogue →
Vista de Satsana Duct (Ender 3) for Nebula bracket + CR Touch + G sensor

Satsana Duct (Ender 3) for Nebula bracket + CR Touch + G sensor

Satsana Duct (Ender3) for Nebula bracket + CR Touch + G sensor Purpose This model is a remix of the original Satsana duct designed specifically for the Ender 3. It is modified to accommodate a CR Touch holder that integrates the vibration sensor from the Nebula Pad. By keeping the CR Touch in its original position, this design eliminates the need to manually set X or Y offsets. Practical Uses This duct is intended for users upgrading an Ender 3 with a Nebula bracket, allowing for the simultaneous use of a CR Touch and a vibration sensor while maintaining standard probe positioning. Included Parts - Satsana_CR_Touch_remix_mymod_v2.stl Printing and Assembly Guidance According to the author, the same printing settings used for the original Satsana model can be applied here. However, small supports are required in specific areas: where the screw is located and where the CR Touch piece is held.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Ender 3/Pro/5/Cr-10 Knob for Extruder

Ender 3/Pro/5/Cr-10 Knob for Extruder

Ender 3/Pro/5/Cr-10 Knob for Extruder Purpose This model is a replacement or upgrade knob designed specifically for use on a 3D printer extruder. Practical Uses According to the author, this part is intended to be printed and placed onto the existing extruder knob. It is reported to be compatible with the Ender 3, Ender 3 Pro, Ender 5, and CR-10 models. The author notes that it might also work with most other Ender series printers. Included Parts - Ender_3_Extruder_Knob1.stl

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Ender 3 CR-Touch Mount

Ender 3 CR-Touch Mount

Ender 3 CR-Touch Mount Purpose This part is designed to facilitate the installation of a CR-Touch sensor. Its primary function is to allow the sensor to be positioned as close to the extruder as possible. Practical Uses This mount is intended for use with Ender 3 series printers to optimize the placement of the CR-Touch probe relative to the extruder assembly. Included Parts - MY_ender-3-cr-touch-mount.stl Printing and Assembly Guidance Not provided in the source text.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de BMG Aero Direct Extruder Mount For CR-10

BMG Aero Direct Extruder Mount For CR-10

Purpose This model provides an extruder mount and a layer fan mount designed for the Mellow Store. It is intended for use with a CR-10 or Ender 3 style carriage paired with an E3D volcano extruder. Practical Uses The components allow for the mounting of an E3D volcano extruder and a layer fan onto specific printer carriage configurations. Included Parts - Extruder_Mount.stl - Extruder_Mount_Right_Offset.stl - BLTouch_Mount.stl - Layer_Fan_BLTouch_Rail.stl

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Swissburner Mounting plate for metal BL/CR-touch bracket

Swissburner Mounting plate for metal BL/CR-touch bracket

This mounting plate is designed for the Swissburner mod, which is a Voron Afterburner mod for Ender 3 style printers (not V2). It is intended for users who wish to utilize the metal bracket included with a CR-touch or a BL-touch. The part is compatible with the Micro-Swiss all-metal hotend as well as the Micro-Swiss direct drive with an all-metal hotend. 120-300 words when facts suffice, otherwise be concise.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de CR Touch with Dual Fan

CR Touch with Dual Fan

This model is designed as an alternative mounting solution for users who find that standard setups do not fit a CR Touch. The author notes that this specific configuration required an extension plate for use on an Ender 3 Pro. Practical uses include mounting a CR Touch or BL Touch on an Ender 3 Pro printer when standard dimensions are incompatible. Included parts: - CR Touch Extension.stl - Backplate with CR-Touch.stl

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Ender & CR-10 X Axis Cover Redesign

Ender & CR-10 X Axis Cover Redesign

Ender & CR-10 X Axis Cover Redesign Purpose This model is a redesign of the X-axis cover specifically intended for printer setups where the hotend cables pass in front of the Z axis. Practical Uses It serves as a functional modification for Ender and CR-10 series printers to accommodate specific cable routing requirements. Included Parts - X-Axis Cover Redesign.stl Printing and Assembly Guidance The author reports printing this model using PETG. Users should follow the instructions provided by FedorSosnin for successful implementation.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Ender 3 / CR-10 / Ender 2, etc Nozzle Measurement Tool

Ender 3 / CR-10 / Ender 2, etc Nozzle Measurement Tool

Ender 3 / CR-10 / Ender 2, etc Nozzle Measurement Tool Purpose This tool is designed to help measure the distance between the printer nozzle and the screws used to secure the stock Ender-3 heatsink. According to the author, it is primarily intended to assist in designing new mounts for custom setups. Practical Uses Users can utilize this tool to determine precise spacing for custom hardware configurations. The tool features a scale where each line effectively represents 1mm. The total distance from the center of the screws to the bottom of the tool is 55mm. Included Parts - NozzleGauge.stl Compatibility Designed for use with Ender 3, CR-10, Ender 2, and similar models using the stock heatsink screw configuration.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Hero Me + CR-Touch Modification for Ender 3

Hero Me + CR-Touch Modification for Ender 3

This model is a modified Hero Me setup designed for the Ender 3. It adapts the original Hero Me design to accommodate a Creality CR-Touch leveling probe instead of a standard BLTouch. The set also includes components for a 5015 radial fan cooling system. Users may use these specific files individually or combine them with the original Hero Me design. 1. Purpose: To provide a modified mounting solution for an Ender 3 that supports both a Creality CR-Touch probe and a 5015 radial fan. 2. Practical Uses: Upgrading Ender 3 cooling and leveling capabilities. 3. Included Parts: CR-Touch mount (CR-Touch.stl), 5015 fan pipes (5015_Pipes.stl), and a base (Base.stl). 4. Configuration Data: The author reports the Marlin probe offset as NOZZLE_TO_PROBE_OFFSET { -45.8, -10, 0 }.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de CR Touch shim

CR Touch shim

CR Touch shim Purpose This single shim is designed to provide clearance for wiring and the plug end when the CR Touch is installed using its included bracket. According to the author, this part is required on the Ender 3 V2 when utilizing a Spider V1.0 hotend. Practical Uses It serves as a spacer to ensure proper fitment and wire management during the assembly of the CR Touch probe on specific hotend configurations. Included Parts - 1 piece shim (CR Touch spacer.stl) Printing and Assembly Guidance The author reports printing the part with PLA, though they note there is no reason to believe the model would pose a problem with other materials. The author reports the part has been in use for 12+ hours of print time with no indications of pending failure.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Ender 3 S1 Additional 4010 Fan Mount for Zero Y-offset CR Touch Mount

Ender 3 S1 Additional 4010 Fan Mount for Zero Y-offset CR Touch Mount

This model is a 4010 fan mount designed specifically for the Ender 3 S1. It is intended for users who have already installed the Zero Y-offset CR Touch mount (available at https://www.printables.com/model/359910-ender-3-s1-sprite-extruder-zero-y-offset-cr-touch-). 120-300 words when facts suffice, otherwise be concise. Purpose The mount is designed to attach a spare 4010 fan to the front of the extruder. The author suggests this modification is intended to provide additional cooling performance. Practical Uses It serves as an add-on component for Ender 3 S1 printers that utilize the specific zero Y-offset CR Touch mount configuration, allowing for extra part cooling via a secondary fan. Included Parts The package includes one STL file: ender3-s1-4010-fan-mount.stl. To complete the installation, two M3x12mm screws are required.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de CR Touch Bracket (Ender-3 V2 NEO)

CR Touch Bracket (Ender-3 V2 NEO)

Purpose This model is a recreation of the stock bracket used to hold the CR Touch on the Ender-3 V2 NEO printer. Practical Uses It serves as a replacement part for the original CR Touch mounting hardware. Included Parts - CR Touch Bracket.stl Printing and Assembly Guidance The author recommends printing with PETG, ABS, or ASA using 100% infill and a 0.2 resolution. The part works with the stock M3 screws provided with the printer.

Technology
Sin probar
material
—
Difficulty
Sin especificar