17 modelos etiquetados

#single STL

Descubre modelos 3D etiquetados como single STL y revisa sus datos de impresión, archivos y condiciones de uso antes de descargarlos.Open all filters →

RC & MecánicaGratis

Open-Frame Rear Wing for RC Cars - Single STL

Give an RC car a wide rear-wing profile using the supplied printable spoiler. The geometry has an angular open-frame center, raised end sections, reinforcing surfaces and two mounting tabs with openings. The source photograph shows the wing installed on an off-road RC car; the vehicle, tires and separate mounting support shown there are not included. One STL file is supplied, renamed 01-open-frame-rear-wing.stl in English without altering its geometry. The original filename contains 2MM and TPU labels. These are source labels, rather than a verified thickness measurement or a tested material recommendation. No vehicle scale or specific model compatibility is established by the supplied inventory. Inspect the wing and mounting-tab spacing in your slicer and compare them with your intended RC vehicle before printing. Choose material, orientation and supports to suit the actual geometry. Aerodynamic performance, impact resistance, physical fit and print settings have not been tested by MESHOPIA. No fasteners or assembly instructions are separately included. The cover is a new local visualization based on a Blender render of the actual STL. It shows the wing alone with a different finish, lighting and background.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Textured Service Ramp for 1:10 RC Drift Cars - STL

Add a small raised wheel support to an RC display or workbench setup. The source photograph shows a pair of matching ramps with straight inclined approaches, a repeating circular surface pattern and an elevated flat section supported by an open frame. The source folder and filename label the design for 1:10 RC drift cars. One STL file is included, renamed 01-textured-rc-service-ramp.stl in English without altering the printable geometry. The two physical ramps in the reference show a possible paired setup; the file inventory does not establish two separately supplied variants. Inspect the STL layout and print additional copies as needed. No car or other track equipment is included. Compare the ramp width, surface features and elevated support with your intended tires and vehicle. Wheel fit, load capacity, traction and print settings have not been physically tested by MESHOPIA. Select material, orientation, walls and supports after reviewing the model in your slicer. No separate hardware or assembly guide is documented in this extracted set. The MESHOPIA cover is a studio render of the actual STL geometry, showing one ramp with its circular surface features, recessed rear platform and open supports. The supplied geometry is unchanged; the new finish, lighting and background are part of the visualization.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

T-Handle Rod-End Assembly Tool for RC Linkages - STL

Hold and turn suitable RC rod ends with this printable T-handle tool. The actual STL has a broad contoured grip and a short upright socket with a shaped opening. The supplied photograph shows a linkage laid across the handle as an example of use; that metal linkage, rod ends and other workshop tools are not included. One STL is supplied. Its original filename contains a STEP reference, but the extracted download contains STL geometry rather than a separate editable STEP file. The file is renamed 01-t-handle-rod-end-tool.stl without changing the model. The socket profile and handle contours are preserved. Inspect and measure the socket against your intended rod ends before printing. No supported rod-end sizes, torque rating or physical fit test are documented in this set. Select material, orientation, walls and supports for your own use after inspecting the mesh. The new MESHOPIA cover is a studio render of the exact supplied STL, with a graphite finish and a pale stone background. It shows the printable tool alone.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Twin-Outlet Muffler Detail for an MST E30 RC Drift Body - STL

Add a twin-exhaust visual detail to a suitable MST E30 RC drift-car body. The supplied photograph shows the accessory beneath the rear bodywork. Inspection of the actual STL shows a rounded muffler housing, two curved outlet tubes with open ends, and an angular mounting bracket with reinforcing ribs. This is a decorative RC body accessory. One STL is included, renamed 01-e30-twin-outlet-muffler.stl without changing its geometry. The model contains the muffler and its integrated mounting form. The vehicle, body shell and attachment hardware shown or implied by the reference are not included. No scale is independently established by the supplied folder or filename. Compare the mounting bracket and outlet clearance with your intended body before printing. Compatibility beyond the source MST E30 label, mounting method and physical fit have not been tested by MESHOPIA. Choose material, orientation and supports after inspecting the hollow outlets and bracket in your slicer. The new MESHOPIA cover is a studio render of the actual STL from a new angle on a pale stone surface, with a gray finish. It retains both open outlets and the original mounting geometry.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Flat-Top RC Car Display Stand with Parts Tray - Single STL

Raise a suitable RC car above the work surface with this printable flat-top stand. Inspection of the supplied STL identifies five separate mesh components: a compartmented base with a central socket, a cylindrical support post, a rectangular perforated top plate, and two ring-shaped collars. The base provides six recessed trays for loose parts. The top has grouped circular openings and smaller mounting holes. One STL is included, renamed 01-flat-top-stand-five-part-layout.stl. It contains the five parts in their original separate layout. The geometry and original arrangement in the download are preserved; separate the components in your slicer as appropriate. No vehicle, screws or other hardware are supplied. The MESHOPIA cover uses the actual mesh components, repositioned in Blender to illustrate the base, post and top together. The two collars are shown beside the stand. This is a visualization of component placement; their final seating, fastening, rotation and load capacity have not been physically verified. The pale blue finish, studio angle and stone background were created for the new cover. No vehicle scale is established by the supplied filename. Check the top footprint, clearance and post interfaces against your vehicle before printing. Choose material and orientation for the expected load, inspect supports in the slicer, and test stability before placing a vehicle on the stand. No tested print profile is provided.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Controller Wall Cradle for Traxxas-Style RC Transmitters - STL

Store a compatible pistol-grip RC transmitter on a wall with this shaped cradle. The supplied reference shows a steering-wheel radio resting on the bracket; despite the source folder mentioning TRX Slash, the pictured item is a transmitter holder. Inspection of the STL shows a curved supporting surface, a tall back section, a lower ledge and internal reinforcing ribs. One original STL is included, renamed 01-rc-transmitter-wall-cradle.stl. The controller, wall fasteners and any vehicle are not included. The original mesh is preserved. No vehicle scale is specified by this accessory. Compare the cradle surface and mounting geometry with your own transmitter and inspect the mesh in your slicer. The photograph illustrates one installation but does not establish universal Traxxas compatibility. Mounting method, fastener selection and load capacity have not been tested by MESHOPIA. The new cover renders the actual bracket alone on a pale stone surface with a gray finish and a new camera angle.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

FPV Camera and Transmitter Mount - 19 x 19 and TS5823 Source Labels - STL

Mount a suitable small FPV camera and transmitter together on this compact bracket. The supplied photograph shows an FPV installation on an RC aircraft. Inspection of the actual STL reveals two raised side walls with camera mounting holes, an open central frame, upright rear slots and four rounded mounting feet with holes. One STL is included, renamed 01-fpv-camera-transmitter-bracket.stl. The camera, transmitter, antenna, aircraft, wires and fixing hardware are not included. The original mesh is preserved. Although the filename contains "3mf", the supplied file is an STL. The source identifies a 19 x 19 camera, TS5823 and "No Supports". These are supplied design labels; device compatibility and support-free printing have not been independently tested by MESHOPIA. Compare the actual hole spacing, openings and clearances with your hardware and inspect the part in your slicer. No vehicle scale or tested print profile is supplied. The new cover was created locally in ComfyUI from a render of the actual STL. It shows the bracket alone in a forest-green finish on a pale textured studio surface; the real mounting holes, rear slots and open frame were checked against the mesh.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Vehicle Cradle for a DJI RC2 Controller - Single STL

Position a suitable DJI RC2 controller using this printable vehicle cradle. The supplied photograph shows a controller supported inside a vehicle. Inspection of the actual STL reveals a broad lower ledge, tall curved side retainers with rectangular openings, and a raised rear mounting section. One original STL is included, renamed 01-dji-rc2-vehicle-cradle.stl. The controller, vehicle dashboard, fastening hardware and cables are not included. The original mesh is preserved and no vehicle scale is associated with this controller accessory. DJI RC2 is the supplied source identification; fit, attachment method and stability in a vehicle have not been physically verified by MESHOPIA. Compare the holder openings and contact surfaces with your controller and planned mounting location before printing. Inspect orientation and supports in your slicer. No tested print profile is supplied. The new cover renders the actual holder alone in a blue finish on a pale stone studio surface from a fresh camera angle.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Paddle-Style Snow Tire Sleeve for RC Vehicles - STL

Try a paddle-style tire sleeve on a suitable RC wheel. Inspection of the actual STL shows a hollow cylindrical sleeve with tall radial paddles around its outer circumference. The supplied photograph shows multiple sleeves installed on an RC truck. The download contains the model for one sleeve; print additional copies as needed. One original STL is supplied as 01-paddle-snow-tire-sleeve.stl. The geometry is preserved. No wheel hub, tire, axle hardware or vehicle is included. The purchased archive also contained a reference screenshot; this listing uses a new MESHOPIA cover and publishes the printable model. The source calls this a snow tire, but no independent traction test, load test or verified wheel size is supplied. Compare its inner diameter, width and paddle clearance with your wheel and chassis. Material flexibility and print orientation affect how the sleeve behaves. Inspect the model in your slicer and verify fit before use; no tested print profile or vehicle scale is provided. The new cover renders the exact sleeve alone in a blue finish on a pale stone studio surface, without inventing a wheel center or additional tread.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Robot Mower License Plate with German Placeholder Text - STL

Add a decorative license-plate detail to a suitable robot mower with this printable plate. The supplied photograph shows a personalized plate mounted on a mower; inspection of the actual STL shows a thin rectangular plate bearing a small star-circle emblem, the letter D and the German placeholder word "Wunschtext". The pictured personalized registration is not present in the supplied mesh. One original STL is included, renamed 01-robot-mower-placeholder-plate.stl. Its mesh, including the existing lettering, is preserved. The source filename says "without lettering", but the actual mesh contains the placeholder text described above. No editable CAD file, mower or mounting hardware is included. The plate is a decorative accessory. No scale, mounting fit or tested print settings are established by the supplied files. Personalization would require an additional geometry edit, which has not been applied to this download. Inspect the lettering and plate thickness in your slicer and select a mounting method suitable for your mower. The new cover renders the actual supplied plate on a pale stone surface with a warm ivory finish, retaining its original lettering and emblem.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Low-Profile Rear Wing for a BMW M3 E30 RC Body - STL

Add a low-profile rear-wing detail to a suitable RC body with this one-piece design. Inspection of the supplied mesh shows a long shallow wing, upright end plates and two curved mounting feet. The source identifies BMW M3 E30; this is a supplied application label, and a particular body fit or scale has not been verified. The download contains one original STL, renamed 01-rear-wing-bmw-m3-e30.stl. Its geometry is preserved. The metal clips seen in the supplied photograph are separate hardware and are not included in the mesh. No vehicle body, fasteners or editable CAD file is supplied. Compare the mounting-foot spacing and wing width with your own body shell before printing. Inspect the mesh and choose orientation and material for your intended use. MESHOPIA has not physically tested fit, attachment strength or printing settings. The new studio cover uses the actual wing geometry in a dusty rose finish on a pale stone surface, with a different angle and no added metal clips.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Stepped Obstacle Ramp for RC Crawlers - Single STL

Build a small crawler-course obstacle with this narrow stepped ramp. The supplied mesh has an uneven stepped upper track and open side bracing above a straight base. The reference photograph shows a pair used beneath the two sides of an RC crawler. The download contains one ramp model; print additional copies to create a pair if suitable for your vehicle. One original mesh is supplied as 01-stepped-crawler-obstacle-ramp.stl. No vehicle, connecting hardware or second distinct ramp variant is included. The source geometry is preserved; the cover only rotates the mesh into a standing presentation. No vehicle scale, load rating or tested print profile is established. Check ramp width, clearance and spacing against your crawler tires, and verify stability before driving over it. Inspect the file in a slicer and choose a material and orientation for the expected load. The new cover shows one actual ramp in a teal finish on a pale stone studio floor. It retains the stepped track and original side openings.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Braced Jump Ramp for a Losi Micro-B RC Car - STL

Create a jump feature for a suitable small RC car with this single-piece ramp. Inspection of the actual mesh shows a broad curved approach surface, a rectangular outer frame and triangular bracing beneath and along the sides. The source identifies Losi Micro-B; physical fit, jump behavior and vehicle suitability have not been independently tested. The download includes one original STL, renamed 01-braced-micro-b-jump-ramp.stl. The entire ramp geometry is retained. No vehicle, course floor, fasteners or additional ramp sections are included. The cover rotates the supplied mesh to show it resting in an operating orientation. Check the surface width and approach against your intended vehicle and available space. No vehicle scale, load rating or tested slicer profile is supplied. Inspect the model in a slicer and assess material strength and stability before use. The new studio cover renders the actual ramp alone in a blue finish on a pale stone floor, from a different angle than the supplied yellow-ramp photograph.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Flat CP Riser Tile with Arch Supports - STL

Extend a compatible course layout with this flat CP riser tile. Inspection of the actual STL shows a square flat deck, two elevated side supports with semicircular openings, and rounded tabs and recesses around the edges. The source photograph shows it connected to another course tile. That adjoining blue section is not part of this download. One original mesh is included as 01-flat-cp-riser-tile.stl. The source mesh is preserved. The supplied geometry has a plain deck; the repeated surface pattern visible in the reference photograph is not reproduced in this mesh. No additional course sections, vehicle or editable CAD file is included. The source title does not establish the CP system dimensions, a vehicle scale or tested compatibility. Compare the edge connections and height with your existing course before printing. MESHOPIA has not tested interlocking fit, load capacity or print settings. The new cover renders the actual tile in an olive finish on a pale stone studio surface, retaining its plain deck, arches and original edge features.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Seated Driver Figure for RC Cars and Trucks - STL

Add a seated driver detail to a suitable RC car or truck cab. The supplied STL shows a stocky adult figure with a short-sleeved collared shirt, trousers and lace-up footwear. Both arms extend forward in a driving pose, with the legs bent for a seated position. The source photograph places the figure inside a truck cab; that cab and its steering wheel are not included. The download contains one original STL, renamed 01-seated-rc-driver-figure.stl. It retains the complete source figure and clothing detail. There is no separate seat, steering wheel, dashboard, vehicle shell or editable CAD file. No vehicle scale or verified cab compatibility is established. Measure the figure against your seating space and steering position before printing. Scaling changes clearances and detail. MESHOPIA has not tested installation, print orientation or a slicer profile. The new studio cover presents only the actual seated figure, with a bronze-colored finish and a different viewpoint on a pale oak tabletop with a softly blurred workshop background.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Basic RC Chassis with Open Electronics Box - STL

Build on a simple RC chassis concept with this supplied prototype mesh. The actual STL has a broad rectangular base, an open square electronics enclosure with a narrow front slot, side panels with mounting holes and open motor-support features near the corners. The supplied installation photograph shows motors, yellow wheels and wiring fitted to a printed chassis; those external components are not included in the STL. The original Prototype2 mesh is preserved and renamed 01-basic-rc-chassis-electronics-box.stl. The source layout is retained. This download does not include wheels, motors, batteries, control electronics, wires or fasteners. Inspect the mesh for separate components and decide how to prepare the individual parts in your slicer. No vehicle scale, verified electronics fit or tested print profile is supplied. Check mounting-hole positions, motor dimensions, enclosure space and clearances against your own hardware before printing. MESHOPIA has not tested assembly, driving performance or strength. The new studio cover renders only the actual chassis geometry in dusty rose on a pale wooden workshop surface. The workshop background was generated locally in ComfyUI; the product and its shadows were rendered from the supplied geometry in Blender and composited without changing its shape.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Blue Thunder Helicopter — 3D Printable Display Model

A one-piece helicopter display model with an angular cockpit, rotor and landing-gear details. The package contains one STL; the mesh was visually reviewed and includes an assembled rotorcraft shape. It is a static printable representation; functioning rotor mechanics and flight hardware are not supplied. PACKAGE CONTENTS 2 TXT files, 1 STL file. Exact duplicate files are supplied once. The included file-name map identifies each original path and its renamed counterpart. PRINTING AND ASSEMBLY Parts are supplied separately. Review the build documentation and individual meshes to choose print orientation, material, support strategy and assembly sequence. Printer profiles and G-code are supplied as reference material and must be checked for compatibility before use. Electronics, motors, radio equipment and other purchased hardware are not supplied as physical items. PRESENTATION AND LICENSE Published by MESHOPIA under CC0 on the basis of the rights holder authorization confirmed by the uploader. Original creator references inside supplied documentation are retained. The cover is an original MESHOPIA visualization of the assembled model in an RC hobby setting; it does not document a completed build or a flight test. Assembly and flight readiness have not been independently tested by MESHOPIA.

Technology: Sin probar
material: —
Difficulty: Sin especificar