Meshopia · EnglishEnglish
MESHOPIAScale modelling & RC

55 tagged models · Page 2 of 2

#radiocontrol

Discover 3D models tagged radiocontrol and check their print information, files and terms before downloading.Search this tag in the catalogue →
Vista de Pieza de sujeción del conector de batería para Air65

Battery connector mounting piece for Air65

Replacement plastic part for the connector area of a battery used in an Air65. The author developed it after breaking the original part during an intervention. The publication does not identify the exact battery nor provide an electrical repair procedure, so it is not presented as a universal spare part nor as an instruction for opening a cell. Preparation, compatibility, and printing Check the connector geometry and the available space with the equipment disconnected. The print must not compress the battery, expose contacts, or replace damaged insulation. No material or printing parameters are specified. If the battery is damaged, the printed part does not make it safe or suitable for continued use.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Cubierta antipolvo para Traxxas Slash LCG 4WD

Dust cover for Traxxas Slash LCG 4WD

Cover for the electronics of the Traxxas Slash LCG 4WD that maintains access to the battery swap and the ESC operation. The source describes two variants depending on the position of the ESC button: one for the old 3355X, with visible capacitors, and another for the 3355R. It also offers two solutions for the front intake: a grille with filtering material or a solid piece which, according to the author, does not filter dust from the air. The rear fan is the original Velineon, oriented to exhaust air. Preparation, compatibility, and printing The documented assembly uses nine M3 × 6 screws for the grilles and another M10 × 6 for the connector cover; one M3 × 10 in the front, two M3 × 20 on the side, and four M3 × 10 with four self-locking nuts for the fan. The hinge uses a piece of 1.75 mm PETG filament. First select the ESC variant and check access, wiring, and ventilation. No waterproofing or a complete print profile is certified; keep the air inlets and outlets clear.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Soporte de altavoz Visaton FRS 7 S para Tamiya Scania 770S

Visaton FRS 7 S Speaker Mount for Tamiya Scania 770S

Purpose This mount is designed to install a Visaton FRS 7 S wideband speaker into the roof module of a Tamiya Scania 770S RC model. The construction aims to provide a stable, vibration-reduced, and acoustically optimized mounting solution that integrates into the existing roof structure without altering the vehicle's exterior appearance. Practical Uses The mount allows for the installation of a speaker within the roof so that sound radiates downward into the cabin. It features a low-profile design to prevent collisions with the cabin interior and includes integrated cable management channels to route speaker wires cleanly. Included Parts - Lautsprecher Halterung Scania S770-RC.stl Printing and Assembly Guidance For FDM 3D printing, PETG or ABS is recommended for stability and temperature resistance, while a TPU-hybrid is listed as an alternative for vibration damping. It is suggested to use at least 30–40% infill for stiffness, with 100% infill for critical areas like the screw domes. A thin damping layer, such as a TPU ring or foam rubber, is intended to be placed between the speaker and the mount to minimize resonances.

Technology
Sin probar
material
PETG, ABS
Difficulty
Sin especificar
Vista de Estuche sencillo para Beacon y joysticks HOVERAir X1 Pro/ProMax

Simple case for Beacon and joysticks for HOVERAir X1 Pro/ProMax

Identified carrying case or holder for the Beacon and the joysticks of the HOVERAir X1 Pro/ProMax. The source aims to keep these accessories together and facilitate their preparation. It does not document protection against impacts, water, or dust, nor does it claim to be suitable for transporting the complete drone. Preparation, compatibility, and printing Check which accessories fit into the housings and check their removal before printing. The fit must hold them without pressing buttons or connectors. No material, layer, or infill is documented. An initial test of the cavities will allow checking tolerances without assuming that all revisions of the accessories share the same dimensions.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Balancín trasero monoamortiguador para chasis Sakura D5

Single shock rear bellcrank for Sakura D5 chassis

Two-piece printed assembly for a single shock rear suspension modification on the Sakura D5. The source documentation identifies the assembly and lists the mounting hardware; it does not demonstrate improved grip, progressivity, or strength compared to the original suspension. The download does not include the shock, the chassis, or the hardware. Preparation, compatibility, and printing The source requires a 6 × 10 × 3 mm bearing, two M3 14 mm screws, M3 nuts, and washers. Verify the diagram and the position of each part with your version of the chassis. Before running, check for a smooth travel without hard points, pivot play, and the absence of rubbing. No validated print profile is documented: old generic values for infill, clearance, or material should not be interpreted as author settings. The cover is a contextual illustration, not a physical assembly test.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de Conversión delantera monoamortiguador para chasis Sakura D5

Front mono-shock conversion for Sakura D5 chassis

Two-piece printed assembly to convert the front suspension of the Sakura D5 to a mono-shock configuration. The source indicates that the holes allow for adjusting the axle play and mentions two M3 35 mm screws. It is not a complete suspension: the rest of the assembly depends on the vehicle and the associated components. Preparation, compatibility, and printing Compare the holes with the actual pins and screws before finishing the adjustment. No universal clearance or validated print profile is provided. Check wall continuity and pivot zones in the slicer, avoiding supports that are difficult to remove inside the holes. Once the assembly is presented, check symmetry, rotation, travel, and static interference. The cover shows the parts in an illustrative context; it does not certify a tested assembly or an improvement in car performance.

Technology
Sin probar
material
—
Difficulty
Sin especificar
Vista de M-Jet Sprint · lancha jet RC · kit STL

M-Jet Sprint · lancha jet RC · kit STL

Kit digital de lancha jet RC M-Jet Sprint, diseño de Štěpán Müller (M-Jet Development). Incluye las 18 piezas STL originales, el manual, las modificaciones disponibles y copias con nombres claros. La vista STL principal se ensambló en Blender para el catálogo usando la variante opcional de casco de una pieza; no es una pieza única lista para imprimir. Para imprimir, usa las piezas individuales del ZIP y consulta el manual. Recomendaciones FDM transcritas del manual original: PLA, boquilla 0,4 mm, ancho de extrusión 0,45 mm, 4 perímetros y 5 capas superiores/inferiores. Los ajustes varían por pieza: cascos y cubierta 0,2 mm/15 %; la mayoría de las piezas 0,15 mm/15 %; impulsores 0,1 mm/80 % con soportes; soporte de motor 0,15 mm/80 %; motor y pilotos opcionales 0,15 mm/5 %. Algunas piezas requieren brim. El manual indica que los STL están orientados para imprimir y recomienda imprimir cada pieza por separado. tpiernas no ha probado estos ajustes. Necesita montaje físico y herrajes, rodamientos, juntas, varilla, motor brushless refrigerado por agua, ESC, servo, batería y electrónica, no incluidos. La documentación advierte que no todos los mods se han probado. No se han verificado la estanqueidad ni el funcionamiento RC. La ficha usa CC0 según la autorización de redistribución bajo CC0 declarada por quien publica; el ZIP conserva los avisos originales de procedencia. Fuente: CGTrader · M-Jet Development / Štěpán Müller.

Technology
FDM
material
PLA
Difficulty
Avanzada