Meshopia · EspañolEspañol
MESHOPIAModelismo y radiocontrol

8 modelos etiquetados · Página 1 de 1

#cr touch mount

Descubre modelos 3D etiquetados como cr touch mount y revisa sus datos de impresión, archivos y condiciones de uso antes de descargarlos.Buscar esta etiqueta en el catálogo →
Vista de Adapter CR Touch Qidi X-CF

Adapter CR Touch Qidi X-CF

Adapter CR Touch Qidi X-CF Purpose This model is a small adapter designed for mounting a CR Touch probe to a Qidi X-CF printer. The CR Touch is described as a plug-and-play component. Practical Uses It serves as a mounting solution to integrate the CR Touch probe onto the X-CF printer hardware. Included Parts - CR touch qidi xcf.stl Printing and Assembly Guidance The author reports printing this model with Nylon CF. For assembly, it is recommended to use threaded inserts for 3D prints to ensure functionality. Additionally, the user must cut a slot in the side of the cover to provide necessary clearance for the probe.

Tecnología
Sin probar
Material
—
Dificultad
Sin especificar
Vista de BIQU H2 CR Touch Mount

BIQU H2 CR Touch Mount

BIQU H2 CR Touch Mount Purpose This model is a dedicated mount designed to hold a CR Touch sensor. It is specifically intended for use with the BiQu H2 Ender 5 Plus BlowThrough setup. Practical Uses This component allows for the integration of a CR Touch probe within the BiQu H2 configuration on an Ender 5 Plus BlowThrough printer, facilitating automated bed leveling. Included Parts - BIQUH2 CR TOUCH.stl Printing and Assembly Guidance No specific printing or assembly instructions are provided in the source documentation.

Tecnología
Sin probar
Material
—
Dificultad
Sin especificar
Vista de Manta MK2 CR Touch Mount Center Mount

Manta MK2 CR Touch Mount Center Mount

Manta MK2 CR Touch Mount Center Mount Purpose This model is designed for the Manta MK2 Ender V1/V2 system to allow the CR Touch to be used as the sensor instead of the BLTouch. Practical Uses It serves as a center mount for the CR Touch. When installing, the user suggests using the included spacer to adjust the CR Touch approximately 3mm above the nozzle to prevent crashes or incorrect Z-offset readings. Users may also use the 2mm side of the spacer or flush the CR Touch to the bed, though the 3mm spacing is recommended. Included Parts The files provided include the Manta CR Touch V3 STL and a 3MF file. Printing and Assembly Guidance For printing, the source suggests using PETG, ABS, or stronger materials rather than PLA. If using a high-temperature setup, use high-temperature resistant materials. Recommended print settings include a layer height of 1.6mm or 2.0mm and 100% infill. For ABS and PETG, a speed of 40mm/s is suggested. During assembly, installation involves using washers, screws through the CR Touch and bracket, followed by a washer and a nut. The source notes an X/Y offset of X= -1.8 and Y= -37.5.

Tecnología
Sin probar
Material
—
Dificultad
Sin especificar
Vista de Ender 3 S1 Sprite Extruder CR Touch Adjustable Zero Y Offset Mount

Ender 3 S1 Sprite Extruder CR Touch Adjustable Zero Y Offset Mount

Ender 3 S1 Sprite Extruder CR Touch Adjustable Zero Y Offset Mount Purpose This model is an adjustable mount designed to achieve a perfect zero offset for the CR Touch. It was created to address inaccuracies in printer calibration and to provide a more convenient solution than repeatedly disassembling the extruder from the carriage. Practical Uses It is used on the Ender 3 S1 with a Sprite Extruder to allow for fine-tuning the Y offset of the CR Touch. To assist with alignment, the designer recommends printing a small circle (such as a resized cylinder from Cura) in the center of the print bed to serve as a guide for lining up the sensor. Included Parts - S1 CR Touch Zero Offset Mount.stl - S1 CR Touch Zero Offset Arm.stl Assembly Guidance Assembly requires four M3 screws and four M3 hex nuts, in addition to the two original screws. The designer recommends placing two washers under the adjustable section of the arm to ensure it holds more evenly.

Tecnología
Sin probar
Material
—
Dificultad
Sin especificar
Vista de Reinforced Ender S1 Zero Y Offset CR touch mount

Reinforced Ender S1 Zero Y Offset CR touch mount

Reinforced Ender S1 Zero Y Offset CR touch mount Purpose This model is a reinforced mount designed for the Ender S1 to facilitate the CR Touch zero Y offset. The design features solid bracing to increase structural integrity. Practical Uses It is intended for use on the Ender S1 printer to provide a more robust mounting solution for the CR Touch sensor, specifically addressing the zero Y offset requirement. Included Parts - Reinforced-EnderS1-zero-y-offset.stl Design Details The author reports that the mount includes additional chamfers on both the CR mount and the bracket that attaches to the extruder.

Tecnología
Sin probar
Material
—
Dificultad
Sin especificar
Vista de Kingroon KP5L and KP3s mount for CR Touch sensor

Kingroon KP5L and KP3s mount for CR Touch sensor

kingroon KP5L and KP3s mount for CR touch Purpose This model is a dedicated mount designed for the CR Touch sensor, specifically intended for use with Kingroon KP5L and KP3s printers. Practical Uses It serves as a mounting solution to integrate a CR Touch sensor onto the specified printer models. Included Parts - kingroon CR touch.stl Printing and Assembly Guidance To print this model, use an infill of 20% with a Triangle infill pattern. No supports are required for this print.

Tecnología
Sin probar
Material
—
Dificultad
Sin especificar
Vista de CREALITY CR TOUCH Support Mount

CREALITY CR TOUCH Support Mount

Purpose: This model provides a mount for the Creality CR TOUCH bed auto-leveling sensor. It is designed for use with the Trianglelab DDE type V6 hotend. Practical uses: It allows for the integration of a CR TOUCH sensor onto a Trianglelab DDE V6 hotend setup. Included parts: - Soporte para CR TOUCH.stl Assembly guidance: Installation requires four M3x10mm screws. The author specifies the use of a Creality CR TOUCH sensor.

Tecnología
Sin probar
Material
—
Dificultad
Sin especificar