5 modelos etiquetados

#STL and 3MF

Descubre modelos 3D etiquetados como STL and 3MF y revisa sus datos de impresión, archivos y condiciones de uso antes de descargarlos.Open all filters →

RC & MecánicaGratis

Front Body Post for RC Cars - 60 mm Source Label, STL and 3MF

A printable front body-mount post for an RC car, with a wider lower shaft, a reduced upper section, a rounded tip and a line of transverse holes. Both the source folder and the supplied filenames label the design as a 60 mm front body post. That label is retained for identification; MESHOPIA has not independently verified the printed length or vehicle fit. The download contains one STL and one 3MF project for the labeled front post. Both files are renamed in English while preserving their original contents. They are format alternatives in this set, not evidence of two different post lengths. The 3MF may contain project or printer settings that should be reviewed before use. A body shell, chassis, clips and fastening hardware are not included. Check the lower mounting section, hole positions and required height against your chassis and body. Material, orientation, wall thickness and supports should be selected after inspection in a slicer. Physical fit and a tested print profile have not been verified. The MESHOPIA cover is a studio render of the actual STL geometry, using a new gray finish, angle and background. The holes and stepped shaft are retained.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Five-Spoke Drift Wheel Rim for 1-10 RC Cars - STL and 3MF

Create a wheel-rim option for a suitable 1:10 RC drift car with this five-spoke design. Inspection of the supplied STL shows five broad spokes surrounding the central opening, a deep cylindrical barrel and raised circumferential lips. The folder identifies Tamiya and 1:10; these are supplied compatibility and scale labels. Two original files are included: 01-five-spoke-drift-rim.3mf and 02-five-spoke-drift-rim.stl. They provide the source project and mesh forms of the rim design, rather than a complete set of tires or a vehicle. Project contents and geometry are preserved. Tires, wheel nuts, axles and other hardware are not included. Check axle interface, offset, rim diameter and tire fit against your intended chassis. Compatibility with particular Tamiya models and physical fit have not been independently tested by MESHOPIA. Inspect the files in your slicer and choose material and orientation for your intended use. No tested print profile is supplied. The new studio cover uses the actual STL geometry in a bronze finish, from a new angle on a pale stone surface. It preserves all five spokes and the original barrel.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Angular Van Body for a Kamtom KM3299 RC Vehicle - STL and 3MF

Give a suitable Kamtom KM3299 RC vehicle an angular van-style body with this shell design. The supplied STL shows a tall roof with longitudinal ribs and raised front details, open windshield and side-window apertures, wheel arches, sculpted side panels and a prominent front bumper and grille. Kamtom KM3299 is a source application label; physical compatibility has not been independently verified. The download includes 01-kamtom-km3299-van-body.stl and 02-kamtom-km3299-van-body.3mf. These original mesh and project files are preserved. The photographed wheels and underlying RC vehicle are not included in this body-shell download. No glazing, electronics or mounting hardware is supplied. Check shell width, wheelbase, arch clearance and attachment points against your own vehicle before printing. The source does not establish a verified scale or a tested print profile. MESHOPIA has not tested fit or attachment strength. Inspect both files in your chosen slicer and review any source project settings before use. The new studio cover shows only the actual body shell in a copper-red finish on a pale oak workshop table, preserving its open windows and empty wheel arches.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Go-Kart Conversion Parts for an OBZ 1-28 RC Car - STL and 3MF

Give a suitable OBZ RC car a go-kart appearance with this printable conversion collection. The source identifies an OBZ 1:28 car. Inspection of the actual files shows a helmeted upper-body driver holding a steering wheel, a broad front bumper with a sloping nose panel, two curved side panels, an open mounting frame and several small attachment components. The download includes 01-obz-kart-conversion-components.stl, 02-obz-kart-conversion-project.3mf and 03-obz-kart-driver-and-front-bumper.stl. These original source files are preserved. The complete component STL contains separate parts in a preparation layout; the additional driver-and-bumper STL presents the driver and front group together. The 3MF contains its source project arrangement. Inspect the separate objects and any project settings in your slicer. This is a conversion-parts download. The existing OBZ chassis, wheels, tires, motors, batteries, electronics and fastening hardware seen in the supplied installation photograph are not included. Physical compatibility and assembly strength have not been independently tested. Compare mounting positions and clearances with your own vehicle before printing. The 1:28 label comes from the source and does not establish that every part will fit all cars at that scale. The new studio cover arranges only supplied geometry into an illustrative conversion layout: the driver and front bumper are shown with the mounting frame and side panels, and seven small source components are placed alongside. No wheel or electronics geometry has been invented. The original downloads retain their source layouts. This visual arrangement is not an assembly instruction or a fit test. MESHOPIA has not verified operation or print settings.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

RC Transmitter Wall Brackets with Two Retaining Arms - Five Size Variants STL and 3MF

Store an RC transmitter on a printed wall bracket selected to suit its handle or support interface. The inspected parts have a rounded rectangular backplate, two countersunk mounting holes, two projecting arms with raised end stops, and a curved central clearance. The five variants change the backplate and arm spacing or depth. Six unchanged files are included: five individual STL variants and a 3MF source layout containing the five bracket designs. The source size labels are 58x24, 58x30, 58x40, 68x40 and 68x57 mm. English filenames preserve those labels; they are not independently verified fit dimensions. Measure your transmitter and inspect the actual geometry before choosing a variant. The project refers to plane, drone, car and boat transmitters without specifying verified brand or model compatibility. The new cover shows the five actual bracket variants separately in blue and sand colors. The transmitter, wall, screws, anchors and other mounting hardware from the source photograph are not included. Select suitable fixings for your wall and assess the mounting-hole seating, arm clearances and supported weight. No tested load rating, wall-installation procedure or printing profile was supplied. MESHOPIA has not tested installation, fit, strength or printing settings. The cover renders the actual geometry and shadows in Blender, then composites them over a workshop background generated locally in ComfyUI.

Technology: Sin probar
material: —
Difficulty: Sin especificar