Información del modelo
Descripción
This RC F1 Powerboat kit consists of a 70cm F1 hull and a Mercury Racing 360 style outboard engine. The outboard engine stands 20cm in height and is designed for use with hulls 70cm or larger. It features a water-cooling system, a gear lubricant hole, and adjustable trim and height mounting.
Practical Uses
This kit is designed for remote-controlled watercraft enthusiasts. The outboard engine is versatile, intended to be compatible with various hulls above 70cm.
Included Parts
- Outboard Engine Components: 2x 4mm 15t 0.8 bevel gear shafts, 1x 604zz bearing, 5x 684zz bearings, 4mm 30cm shaft, 4mm drive dog, rigid coupler joint (4x5), propeller (up to 50mm), brushless motor (up to 4076 size), 18x M2.5 heat inserts, 18x M2.5x5 screws, 2x M3 x35/40 screws with nuts, 1x M2x3 self-tapping screw, and 2x push rod connectors.
- Hull Components: 16x M3x8mm screws, 4x M3x25mm screws with nuts, 3x M3x40mm screws with nuts, and push rod or stainless steel leader fishing wire.
Printing and Assembly Guidance
- Outboard Engine: Use a 0.4mm nozzle with 0.15mm layer height. Set 5 perimeters, 5 top/bottom layers, and 30% infill. No support is required. The author used PLA for the main body and ABS for the motor mounting.
- F1 Hull: Use a 0.4mm nozzle with 0.2mm layer height. Set 2/3 perimeters, 4 top/bottom layers, and 15% infill. Support is only required for the servo mount.
- General FDM Settings: 0.4mm nozzle, 0.2mm layer height, 4 perimeters, 4 top/bottom layers, and 30% infill.
Texto original del autor en Printables
<p>Build video <a href="https://youtu.be/SllnjgBfWdE?feature=shared">https://youtu.be/SllnjgBfWdE?feature=shared</a><br><a href="https://youtu.be/PSYab_l4kDQ?feature=shared">https://youtu.be/PSYab_l4kDQ?feature=shared</a><br>####Mercury Racing 360 Outboard Engine###</p><p>Outboard file link https://cults3d.com/:2254330</p><p><br>-This outboard has a height of 20cm<br>-Suitable for hulls above 70cm, I will make many hulls that fit this outboard Engine! so you can make lots of rc boats with just one engine<br>-I used a 3670 motor, this outboard can use motors up to 4076 (not tested yet). <br>-this outboard can adjust trim position on mounting and and can be adjusted the height from hull<br>-gear lubricant hole for easier to fill the lubricant after playing<br>-easy to print without any support and pre orianted<br>-need 400grams of filament (pla) used abs for motor mounting<br>-have a great watercooling system</p><p>Print Setting:<br>-min print area = 200x140x50<br>-nozzle = 0.4<br>-layer hight = 0.15 lower is better for high quality<br>-perimater = 5 wall line<br>-top/bottom = 5<br>-infill = 30%<br>-support = no</p><p>BOM:<br>-bevel gear shaft 4mm 15t 0.8 2pcs ( <a href="https://a.aliexpress.com/_opczqfU">https://a.aliexpress.com/_opczqfU</a> )<br>-bearing 604zz 1 pcs ( <a href="https://a.aliexpress.com/_oCFW9Pv">https://a.aliexpress.com/_oCFW9Pv</a> )<br>- bearing 684zz 5pcs ( <a href="https://a.aliexpress.com/_oCFW9Pv">https://a.aliexpress.com/_oCFW9Pv</a> )<br>- shaft 4mm 30cm<br>- rigid couple joint 4x5 (depending on the motor you use) ( <a href="https://a.aliexpress.com/_oDoRGWb">https://a.aliexpress.com/_oDoRGWb</a> )<br>-drive dog 4mm ( <a href="https://a.aliexpress.com/_okQpmtp">https://a.aliexpress.com/_okQpmtp</a> )<br>-propeller up to 50mm (i use 40mm diamter) (<a href="https://a.aliexpress.com/_olAepaR">https://a.aliexpress.com/_olAepaR</a> )<br>-brushless motor up to 4076 ( i used 3670 2150kv)<br>- heat insert m2.5 (2.5IDx3Lx3.5OD) 18pcs ( <a href="https://a.aliexpress.com/_olfvCxz">https://a.aliexpress.com/_olfvCxz</a> )<br>- m2.5x5 18 pcs ( <a href="https://a.aliexpress.com/_oEKdBSR">https://a.aliexpress.com/_oEKdBSR</a> )<br>-m3 x35/40 2pcs with nut (for adjustable trim position)<br>-m2x3 self taping screw (for gear lubricant hole)<br>-push rod connector 2pcs for servo rod ( <a href="https://a.aliexpress.com/_olInPFh">https://a.aliexpress.com/_olInPFh</a> )</p><p>####F1 Hull PowerBoat####<br>-70cm length<br>-Nice desain and performance<br>-easy to build and print withoutsupport<br>-have a pin joint for each body to make easier to put it together<br>-need 1.300gram of pla</p><p>Print Setting:<br>-Min print area = 235x235x230<br>-nozzle = 0.4<br>-layer hight = 0.2 lower is better for high quality<br>-perimater = 2/3 wall line<br>-top/bottom = 4<br>-infill = 15%<br>-support = only servo mount</p><p>BOM<br>-m3x8mm 16pcs for battrey tray, esc tray, servo mount, and servo<br>-m3x25mm 4pcs and nut 4pcs for outboard mount<br>-m3x40mm 3pcs and nut 3pcs for cover <br>-Push rod or stainless stell Leader Fishing wire for servo rod</p><p>Electronic that i used<br>-Battrey 2pcs lippo 2s 5000mah<br>-Esc Flycolor 150a<br>-Servo 25kg waterproof<br>-dumborg 6ch transmitter</p><p>3D PRINTING SETTINGS</p><p>3d printer fdm<br>-nozzle = 0.4<br>-layer hight = 0.2 lower is better for high quality<br>-perimater = 4 wall line<br>-top/bottom = 4<br>-infill = 30%<br>-support = no</p>
Preguntas y aportaciones