4 modelos etiquetados

#RC rear wing

Descubre modelos 3D etiquetados como RC rear wing y revisa sus datos de impresión, archivos y condiciones de uso antes de descargarlos.Open all filters →

RC & MecánicaGratis

Open-Frame Rear Wing for RC Cars - Single STL

Give an RC car a wide rear-wing profile using the supplied printable spoiler. The geometry has an angular open-frame center, raised end sections, reinforcing surfaces and two mounting tabs with openings. The source photograph shows the wing installed on an off-road RC car; the vehicle, tires and separate mounting support shown there are not included. One STL file is supplied, renamed 01-open-frame-rear-wing.stl in English without altering its geometry. The original filename contains 2MM and TPU labels. These are source labels, rather than a verified thickness measurement or a tested material recommendation. No vehicle scale or specific model compatibility is established by the supplied inventory. Inspect the wing and mounting-tab spacing in your slicer and compare them with your intended RC vehicle before printing. Choose material, orientation and supports to suit the actual geometry. Aerodynamic performance, impact resistance, physical fit and print settings have not been tested by MESHOPIA. No fasteners or assembly instructions are separately included. The cover is a new local visualization based on a Blender render of the actual STL. It shows the wing alone with a different finish, lighting and background.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Low-Profile Rear Wing for a BMW M3 E30 RC Body - STL

Add a low-profile rear-wing detail to a suitable RC body with this one-piece design. Inspection of the supplied mesh shows a long shallow wing, upright end plates and two curved mounting feet. The source identifies BMW M3 E30; this is a supplied application label, and a particular body fit or scale has not been verified. The download contains one original STL, renamed 01-rear-wing-bmw-m3-e30.stl. Its geometry is preserved. The metal clips seen in the supplied photograph are separate hardware and are not included in the mesh. No vehicle body, fasteners or editable CAD file is supplied. Compare the mounting-foot spacing and wing width with your own body shell before printing. Inspect the mesh and choose orientation and material for your intended use. MESHOPIA has not physically tested fit, attachment strength or printing settings. The new studio cover uses the actual wing geometry in a dusty rose finish on a pale stone surface, with a different angle and no added metal clips.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Split Rear Wing and Braced Supports for 1:8 RC Projects - STL STEP and 3MF

Build a rear-wing accessory for a 1:8 RC project from this collection of original printable and CAD files. The inspected geometry includes two curved wing halves with outer endplates, a narrow curved center strip and a triangular braced support with a mounting plate. The source labels the design 1:8. The car in the supplied reference photograph is not included. Five original files are preserved: one STEP support-leg file, separate STL files for the left wing half, right wing half and center strip, and a 3MF containing the wing components and two support instances. The 3MF places both support instances at the same coordinates; the new cover separates them into two positions and arranges the wing halves around the center strip. This is an illustrative assembly inferred from the geometry and photograph, not a verified fit. The source download retains its original layouts and coordinates. English filenames identify each component and format. Check the center joint, mounting-plate holes, required support spacing and your car body before printing or installing. Fasteners, a car body and tested mounting hardware are not supplied. MESHOPIA has not tested assembly, strength, aerodynamics or vehicle compatibility, and no tested printing profile was supplied. The new teal-and-copper cover uses the actual source geometry rendered in Blender, with a workshop background generated locally in ComfyUI. The compositing preserves the shapes of the supplied parts.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Curved Rear Wing with Mounting Arms for RC Body Projects - STEP and 3MF

Add a curved rear-wing detail to an RC body project with these original CAD and 3MF files. The inspected geometry includes a long curved wing, raised outer end details, two projecting mounting arms and cylindrical mounting features. The source collection refers to Skoda and Punto, but it does not provide an independently verified body model, scale or mounting interface. Those names identify the source context rather than guaranteed compatibility. Two unchanged files are included: a 3MF source layout and its separately supplied STEP CAD file. English filenames identify the curved rear wing and the file format. The new cover shows only the actual wing geometry in blue, preserving the arrangement of the inspected 3MF components. The painted RC car body and display in the original photograph are not included. Check the mounting-arm spacing, cylindrical features, body curvature and wing dimensions against your project before printing or editing the CAD. Fasteners and a vehicle are not supplied. MESHOPIA has not tested installation, strength, aerodynamics or printing settings. No declared vehicle scale or tested printing profile was supplied. The cover renders the actual geometry and shadows in Blender, then composites them over a workshop background generated locally in ComfyUI without changing the part shapes.

Technology: Sin probar
material: —
Difficulty: Sin especificar