4 modelos etiquetados

#four STL files

Descubre modelos 3D etiquetados como four STL files y revisa sus datos de impresión, archivos y condiciones de uso antes de descargarlos.Open all filters →

RC & MecánicaGratis

Ribbed Truck Bed Cover Parts for MN82 RC Projects - Four STL Files

Add a ribbed bed-cover accessory to an MN82 RC truck project. The supplied meshes contain a U-shaped mounting frame with projecting attachment tabs, a corrugated cover panel with a raised pull tab, and two mirrored side components with long guide forms and spiral-shaped ends. The source names the MN82; no independently verified vehicle scale or mounting specification is supplied. The truck shown in the original photograph is not included. Four unchanged STL files are included, renamed in English to identify the frame, ribbed panel and left and right spiral-ended guides. The new cover places the actual panel over its frame as an illustrative arrangement and shows both guide components separately so their geometry remains visible. No truck body, fasteners or extra mechanism has been added. The illustration does not establish the final guide orientation or a verified moving assembly. Inspect the frame tabs, guide profiles, panel clearances and mounting dimensions against your particular MN82 before printing. Although the source calls this a hard roll-up bed cover, MESHOPIA has not tested rolling operation, flexibility, fit or strength. No tested printing profile or assembly instructions were supplied. The new cover applies teal and copper colors to the actual source geometry. Blender renders the parts and shadows; a locally generated ComfyUI workshop background is composited around them without changing their shape.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Angular Buggy Body Shell Wing and Retainers for RC Projects - Four STL Files

Customize an RC buggy project with these exterior and retaining parts. The inspected body shell has a raised angular cabin, projecting front and rear mounting tabs with square openings, and open lower side clearances. The separate rear wing has a shallow curved deck, raised edges and two mounting holes. The other files contain a square-section body post with a round flange and multiple transverse holes, and a bent retaining-clip form. Four original STL files are preserved and renamed in English to identify the body shell, rear wing, adjustable post and retaining clip. The new cover shows those actual source components separately so the smaller attachment parts can be seen. The completed car in the source photograph uses additional components that are not present in this download: a chassis, wheels, suspension, motor and electronics. No exact vehicle interface or declared model scale was supplied. Check the shell openings, body-post shape and hole spacing, clip engagement and wing mounting holes against your own buggy before printing. The files provide exterior and retaining parts, rather than a verified complete RC vehicle. MESHOPIA has not tested compatibility, clip flexibility, assembly or strength; no tested printing profile was supplied. The new rose-and-blue cover renders the source geometry and shadows in Blender, with a locally generated ComfyUI workshop background composited around the unchanged part shapes.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Six-Spoke RC Wheel Rims with 11 mm and 9 mm Source Labels - Four STL Files

Four compact six-spoke RC wheel-rim meshes with cylindrical barrels, raised outer lips and central mounting features. The two deeper variants have recessed central cavities and engraved detail around the outer lip. The two shallower variants show a shaped mounting opening at the center. All four actual meshes were inspected individually. The source folder is named rc car, but its archive contains wheel rims rather than a complete vehicle. Four unchanged STL files are included with English names that distinguish the paired 11 mm and 9 mm source-labeled variants. The deeper filenames also mention a 9 mm tire skin and a thickened outer ring; the shallower filenames mention a thickened outer ring. These are source labels, not tested dimensions, tire compatibility or verified tolerances. The meshes have approximately 21 coordinate units across their outer diameter, with depths near 11 and 9 units; STL does not itself establish physical units. The new cover displays all four supplied variants, with blue deeper rims, sand-colored shallower rims, a changed camera angle and a new workshop background. Original mesh details are retained. No tires, axles, wheel nuts, hubs or complete RC car are included. Check axle shape, center opening, rim offset, tire seating, side-wall clearance and material strength against your vehicle before printing. MESHOPIA has not tested printing, tire fit, mounting or driving performance. The cover renders the actual geometry and shadows in Blender and composites them over a workshop background generated locally in ComfyUI.

Technology: Sin probar
material: —
Difficulty: Sin especificar

RC & MecánicaGratis

Micro Servo Robot Chassis and Wheels for a Two-SG90 RC Project - Four STL Files

An open rectangular robot-car chassis with ribbed interior sections, two mounting openings and small axle holes, supplied with two drive-wheel variants and a smaller rear-wheel design with an integral shaft. The larger drive wheels have four rounded openings, a central bore and repeated angled fins around the circumference. The rear wheel has four openings and a long stepped shaft. The source project is labeled for two SG90 micro servos. Four unchanged STL files are included with English names: the chassis, standard drive wheel, TPU-labeled drive-wheel variant and rear wheel with shaft. The two drive-wheel meshes have matching overall extents, but their distinct original files are preserved. TPU is a source filename label, not a tested material recommendation or supplied print profile. No tested SG90 fit or servo-modification instructions were included. The cover uses the actual chassis and wheel geometry in a visual assembly. One drive-wheel design and one rear-wheel design are repeated and mirrored across the chassis center, matching the source wheel positions. The chassis is slightly inclined to bring the two wheel sizes to the same ground plane. The alternative TPU-labeled wheel appears beside the assembly. Blue, sand and graphite finishes, a changed angle and a new workshop background replace the source presentation. This arrangement is illustrative and is not a verified mechanical assembly. Servos, servo horns, controller, receiver, battery, wiring, fasteners and any separate electronic components shown in the source photo are not supplied. Check shaft retention, wheel mounting, servo opening dimensions, underside clearance and electronics space before fabrication. MESHOPIA has not tested printing, assembly, load capacity, drive control or operation. The cover renders the actual geometry and shadows in Blender and composites them over a workshop background generated locally in ComfyUI.

Technology: Sin probar
material: —
Difficulty: Sin especificar