Meshopia · EnglishEnglish
MESHOPIA

2 modelos etiquetados

#archivo STEP

Descubre modelos 3D etiquetados como archivo STEP y revisa sus datos de impresión, archivos y condiciones de uso antes de descargarlos.Open all filters →
3D

Tiltable desktop organizer with interchangeable dividers

This organizer allows for placing fine tools, small connectors, or workpieces in separate compartments and orienting the assembly to the most comfortable position. The rectangular body rotates between the triangular arms of a wide base and is immobilized by two printed screws, one on each side. A single interchangeable divider is installed inside the body: the available variants create 6, 8, 10, 12, 14, 16, or 27 cells, allowing the layout to be adapted to the diameter and quantity of the objects to be organized. The official source was updated after the initial import. The author added a main body and two new screws to correct the thread direction, which had been reversed on one side when mirroring the original design. For a new assembly, use Main_Body_Updated.stl, Screw_1_Updated.stl, and Screw_2_Updated.stl along with Main_Stand.stl and only one of the dividers. The previous files are kept as part of the CC0 publication, but they are not the recommended reference. Optional_2nd_Body_print_if_needed.stl is an optional part and is not part of the basic five-piece set. Printing is intended for FDM without supports. The support is placed flat on its base, the body rests on its back face, and the screws are oriented on their top face, following the author's instructions. As a starting point, use a 0.4 mm nozzle, 0.20 mm layers, between three and four perimeters, and a 15% gyroid infill. PLA is sufficient for desktop use; PETG provides more toughness to the arms and the threads, while ABS can be used if a closed printer and a stable configuration are available. The threads require a well-calibrated first layer and a prudent dimensional compensation. Before assembly, remove strings or burrs from the pivots, the side housings, and the threads. Place the updated body between the arms of the stand, insert each updated screw into its corresponding side, and rotate them without forcing. Adjust the tilt and tighten only until the body is immobilized. Then place a divider inside the body and check that it sits without deforming it. If the thread offers abnormal resistance, do not use pliers or increase the torque: check orientation, tolerance, and screw selection. Stability depends on the surface, the tilt, and the load distribution. Place the heaviest objects near the center and do not use the organizer as a handle, structural support, or base for equipment. The cells do not have a universal measurement for all pens, cables, or tools; it is advisable to compare the actual dimensions with the chosen divider. The part does not include electrical insulation, protection against liquids, or certification for industrial environments. The 21 current geometric files were verified: 15 STL and 6 STEP. All STLs have finite coordinates, zero degenerate triangles, a watertight mesh, and consistent orientation; the STEP files feature an ISO-10303-21 header and do not include external references. No G-code, images, PDFs, or machine files were found in the current official source. The new cover was generated exclusively from a technical render of the updated five-piece set assembled with the 27-cell divider.

Technology
FDM
material
PLA, PETG, ABS
Difficulty
Fácil
Vista de Cubierta frontal personalizable para emisora RC

Customizable front cover for RC transmitter

This cover serves as a front housing to develop a radio control handle or a custom electronic panel. The piece combines in a single casing an upper rectangular window, two circular openings for control mechanisms, and several small apertures distributed across the front. The deep perimeter edge provides volume for subsequent assembly, but the package does not include a back to close the assembly. The geometry measures approximately 230.10 × 42.91 × 207 mm and should be understood as a design base, not as a universal housing. The download includes a printable STL and an editable STEP of the same design. It does not include a screen, joysticks, antenna, switches, battery, electronic board, connectors, screws, cables, or a back cover. These elements, if shown in a usage scene, are generic and external references. The openings allow for planning a control layout, but their diameter, position, and depth do not demonstrate compatibility with commercial components. The STEP source facilitates modifying the part; after any change, a new mesh must be generated and geometric and dimensional validation must be repeated. The audited STL has 7,118 vertices, 14,396 triangles, and a single closed, manifold component without detected topological defects. The STEP presents a complete ISO-10303-21 structure with a BREP solid and 351 advanced surfaces; surface-to-surface equivalence between both representations has not been demonstrated. The cover is large, so the useful volume, the head travel, and the stability of the orientation must be checked. A wide face can offer support, but the decision must preserve the edges of the windows and avoid trapped supports. As a reasonable starting point: 0.20–0.28 mm layers, four perimeters, and moderate infill, with local reinforcements only where the actual assembly justifies them. Print partial templates of the openings and design closures, ventilation, insulation, and strain relief separately. Possible uses. Build the front of a custom RC transmitter from measured components. Test the ergonomics and spacing of two joystick mechanisms. Test the position of a screen and auxiliary controls on a desktop panel. Modify the STEP source to adapt windows, mountings, and thickness to your own project. Create a non-critical interface mockup for robotics or teleoperation. Preparation and printing. Measure the screen, joysticks, connectors, switches, board, and hardware before modifying or slicing the front. Print partial templates of each opening to adjust diameters, radii, thickness, and clearances with minimal material. Confirm that the 230.10 × 42.91 × 207 mm box fits within the build volume and does not invade the head travel. Compare orientations on wide faces, protecting the edge of the window and the two circular openings. Start with 0.20–0.28 mm layers and four perimeters; adjust the infill based on the achieved stiffness rather than a universal figure. Place supports only where they can be removed without closing openings, damaging housings, or reducing the wall section. Use PETG if toughness is needed or ASA for an evaluated thermal environment; PLA is suitable for indoor fit prototypes. Assemble first without a battery, check edges, clearances, and retention, and check insulation and cable relief before powering the electronics. Limits and checks. Does not include back, screen, joysticks, electronics, antenna, battery, hardware, connectors, or wiring. There is no verified compatibility with a specific transmitter, board, screen, or control mechanism. The STEP is kept as an editable source, but it has not been fully compared to the STL via a CAD kernel. No testing has been performed for load, impact, drop, vibration, temperature, flammability, or environmental protection. The data sheet does not certify electrical insulation, radio frequency, ergonomics, autonomy, or battery safety. It must not be used for critical control until design, assembly, functional testing, and safe stop measures are completed. The local file preserves exclusively the supported 3D files and a new proprietary cover. The image is a photorealistic editorial interpretation based on the audited geometry: it shows the context of use but does not replace the measurements, the slicer preview, a physical fit test, or the instructions of the associated equipment. Before manufacturing, it is advisable to check scale, units, orientation, supports, path, material, and environment. After printing, remove strings and burrs, check for cracks or weak layers, and discard any copy that does not support, fit, or function stably.

Technology
Sin probar
material
—
Difficulty
Sin especificar